Step 1 : Connect the VGA ISP of flashing programmer with the VGA port of liquid crystal board using VGA line(using the original packing VGA line);
Step 2 : At first click thein the software interface to set;
Step 3 :
Set when the window pops up.
VGA line orders type : The different mainboard will use the different line orders, if it can’t on line,please choose different line orders to test repeatedly.
Serial port speed : That is baud rate adjustment,the baud rate of different mainboard is different.If the printing message is messy code please try to change the baud rate.
After adjusting the parameter please click to save.
Step 4 : After setting the parameter,click,open the serial and electrify the mainboard in 2 seconds,the printing message will appear in the following dialog.
Attention : If the printing message haven’t been appeared,please pay attention to following questions
First click,then supply power to the mainboard;
Some mainboards need to be supplied power in the stand-by mode and also the main power supply;
If the line orders are not correct,please change it in the parameter setting and then try again;
When the serial port of some mainboards is at HDMI or reserved port,it needs to connect HDMI or fly lines,that is to connect SCL,SDA,GND lines with the SCL,SDA,GND on the mainboard;
The serial ports of some mainboard need to be opened in the factory pattern.
- Note
- Manual Organization
- ⅠGeneral Description
- 1.1 What is RT809H?
- 1.2 Programmer Characteristic:
- 1.3 System Requirement
- 1.4 Programmer External Port Instruction
- 1.5 Programmer Packing
- Ⅱ Installing
- 2.1 Software download
- 2.2 Installing the Main Software
- 2.3 Manual Installing the drivers
- 2.4 Installing tool chain panel
- Ⅲ The Software Instruction
- 3.1 Software Interface Instruction
- 3.2 The Toolchain
- Ⅳ Detailed Operation
- 4.1 24XX,25XX,93XX Series Chips’ Reading and Writing
- 4.1.1 93XX’s Reading and Writing
- 4.1.2 24XX,25XX’s Reading and Writing
- 4.2 PLCC Encapsulation Chip’s Reading and Writing
- 4.3 TSOP48 Encapsulation Chip’s Reading and Writing
- 4.4 EMMC’s Reading
- 4.5 Laptop EC Chip’s Reading and Writing
- 4.5.1 1:85XX Series EC Chip’s Reading and Writing
- 4.5.2 KB9012 Chip’s Reading and Writing
- 4.5.3 NPCE 288,388 Chip’s Reading and Writing
- Ⅴ ISP (on-line) Application Instruction
- 5.1 Checking Liquid Crystal Board Printing Message
- 5.2 LCD TV Mainboard Program’s Transcription
- 5.2.1 MST scheme
- 5.2.2 Burning Method
- 5.2.3 MTK Scheme Flashing Method
- 5.2.4 RTD Scheme
- 5.2.5 EMMC_ISP Reading and Writing Tutorial
- 5.2.6 On-line Reading IT85XX Series Laptop EC Chip
- Ⅵ Laptop EC Chip MEC16xx Read-Write
- Ⅶ Secure CRT Software Installation
- Ⅷ Common Problem Diagnosis
- 8.1 Installing the software and driver unsuccessfully
- 8.2 Programmer Unconnected with the Mainframe
- 8.3 The use of programmer selftest command,to check if there is problem itself
- 8.3.1 Selftest way 1:
- 8.3.2 Selftest way 2 :
- 8.4 The Method of Solving the Problem When reading 25XX,24XX,93XX
- 8.4.1 Handling Method
- 8.5 The Method to Solve the Problem of Off-line Read and Write EMMC
- 8.6 The Method to Deal with the LCD Mainboard Printing Information Messy Code
- Ⅸ Guarantee clause：
- Ⅹ Contact Information
- Self-testing